Canary Upgrades

    When installing Istio, the installation setting can be used to deploy multiple independent control planes at the same time. A canary version of an upgrade can be started by installing the new Istio version’s control plane next to the old one, using a different revision setting. Each revision is a full Istio control plane implementation with its own Deployment, Service, etc.

    Before upgrading Istio, it is recommended to run the istioctl x precheck command to make sure the upgrade is compatible with your environment.

    Control plane

    To install a new revision called canary, you would set the revision field as follows:

    In a production environment, a better revision name would correspond to the Istio version. However, you must replace . characters in the revision name, for example, revision=1-6-8 for Istio 1.6.8, because . is not a valid revision name character.

    1. $ istioctl install --set revision=canary

    After running the command, you will have two control plane deployments and services running side-by-side:

    1. $ kubectl get pods -n istio-system -l app=istiod
    2. NAME                                    READY   STATUS    RESTARTS   AGE
    3. istiod-canary-6956db645c-vwhsk          1/1     Running   0          1m
    1. $ kubectl get svc -n istio-system -l app=istiod
    2. NAME            TYPE        CLUSTER-IP    EXTERNAL-IP   PORT(S)                                                AGE
    3. istiod          ClusterIP   10.32.5.247   <none>        15010/TCP,15012/TCP,443/TCP,15014/TCP                  33d
    4. istiod-canary   ClusterIP   10.32.6.58    <none>        15010/TCP,15012/TCP,443/TCP,15014/TCP,53/UDP,853/TCP   12m

    You will also see that there are two sidecar injector configurations including the new revision.

    1. $ kubectl get mutatingwebhookconfigurations
    2. NAME                            WEBHOOKS   AGE
    3. istio-sidecar-injector          1          7m56s
    4. istio-sidecar-injector-canary   1          3m18s

    Due to in the creation of the during install, initial installations of Istio must not specify a revision. As a temporary workaround, for Istio resource validation to continue working after removing the non-revisioned Istio installation, the istiod service must be manually pointed to the revision that should handle validation.

    One way to accomplish this is to manually create a service called istiod pointing to the target revision using this service as a template. Another option is to run the command below, where <REVISION> is the name of the revision that should handle validation. This command creates an istiod service pointed to the target revision.

    Unlike istiod, Istio gateways do not run revision-specific instances, but are instead in-place upgraded to use the new control plane revision. You can verify that the istio-ingress gateway is using the canary revision by running the following command:

    1. istiod-canary-6956db645c-vwhsk

    However, simply installing the new revision has no impact on the existing sidecar proxies. To upgrade these, you must configure them to point to the new istiod-canary control plane. This is controlled during sidecar injection based on the namespace label istio.io/rev.

    1. $ kubectl label namespace test-ns istio-injection- istio.io/rev=canary

    After the namespace updates, you need to restart the pods to trigger re-injection. One way to do this is using:

    1. $ kubectl rollout restart deployment -n test-ns

    When the pods are re-injected, they will be configured to point to the istiod-canary control plane. You can verify this by looking at the pod labels.

    For example, the following command will show all the pods using the canary revision:

    1. $ kubectl get pods -n test-ns -l istio.io/rev=canary

    To verify that the new pods in the test-ns namespace are using the istiod-canary service corresponding to the revision, select one newly created pod and use the pod_name in the following command:

    The output confirms that the pod is using istiod-canary revision of the control plane.

    Stable revision labels (experimental)

    Manually relabeling namespaces when moving them to a new revision can be tedious and error-prone. are a solution to this. Revision tags are stable identifiers that point to revisions and can be used to avoid relabeling namespaces. Rather than relabeling the namespace, a mesh operator can simply change the tag to point to a new revision. All namespaces with that tag will be updated at the same time.

    Consider a cluster with two revisions installed, 1-7-6 and 1-8-0. The cluster operator creates a revision tag prod, pointed at the older, stable 1-7-6 version, and a revision tag canary pointed at the newer 1-8-0 revision. That state could be reached via these commands:

    1. $ istioctl x revision tag set prod --revision 1-7-6
    2. $ istioctl x revision tag set canary --revision 1-8-0

    Namespaces A and B pointed to 1-7-6, namespace C pointed to 1-8-0

    After the operator is satisfied with the stability of the canary tagged control planes, namespaces labeled istio.io/rev=prod can be updated with one action by modifying the prod revision tag to point to the newer 1-8-0 revision.

    1. $ istioctl x revision tag set prod --revision 1-8-0

    Namespaces A, B, and C pointed to 1-8-0

    Namespaces A, B, and C pointed to 1-8-0

    Restarting the injected workloads in namespaces A and B will result in those workloads using the 1.8.0 control plane.

    After upgrading both the control plane and data plane, you can uninstall the old control plane. For example, the following command uninstalls a control plane of revision 1-6-5:

    1. $ istioctl x uninstall --revision 1-6-5

    If the old control plane does not have a revision label, uninstall it using its original installation options, for example:

    1. $ istioctl x uninstall -f manifests/profiles/default.yaml

    Confirm that the old control plane has been removed and only the new one still exists in the cluster:

    Note that the above instructions only removed the resources for the specified control plane revision, but not cluster-scoped resources shared with other control planes. To uninstall Istio completely, refer to the .

    Uninstall canary control plane

    If you decide to rollback to the old control plane, instead of completing the canary upgrade, you can uninstall the canary revision using istioctl x uninstall --revision=canary.

    However, in this case you must first reinstall the gateway(s) for the previous revision manually, because the uninstall command will not automatically revert the previously in-place upgraded ones.

    Make sure to use the istioctl version corresponding to the old control plane to reinstall the old gateways and, to avoid downtime, make sure the old gateways are up and running before proceeding with the canary uninstall.