流

    To define any mesh object as a Flow object, add Fluid physics by clicking Fluid in Properties ‣ Physics. Then select Flow as the fluid Type. Now you should have a default fluid flow source object.

    参考

    面板

    Physics ‣ Fluid ‣ Settings

    类型

    流

    流体类型

    • 烟雾

      Emit only smoke.

      火焰 + 烟雾

      Emit both fire and smoke.

      火焰

      Emit only fire. Note that the domain will automatically create some smoke to simulate smoke left by burnt fuel.

      液体

      Emit liquid.

    流动行为

    Controls if the Flow object either adds (Inflow), removes (Outflow), or turns the mesh itself into fluid (Geometry).

    • 流入

      This object will emit fluid into the simulation, like a water tap or base of a fire.

      流出

      Any fluid that enters the of this object will be removed from the domain (think of a drain or a black hole). This can be useful in combination with an inflow to prevent the whole domain from filling up. Outflow objects can be animated and the area where the fluid disappears will follow the object as it moves around.

      几何数据(Geometry)

      All regions of this object that are inside the domain bounding box will be used as actual fluid in the simulation. You can place more than one fluid object inside the domain. Also make sure that the surface normals are pointing outwards or else they will not simulate properly. In contrast to domain objects, the actual mesh geometry is used for fluid objects.

    Use Flow

    Enables or disables the flow of fluid, this property is useful for animations to selectively enable and disable when fluid is being added to or removed from the domain.

    采样子步长

    Note that these emission sub-steps occur at every simulation step and not per frame. The simulation step count is controlled by the adaptive time stepping.

    烟雾颜色

    The color of emitted smoke. When smoke of different colors are mixed they will blend together, eventually settling into a new combined color.

    绝对密度

    If this checkbox is enabled, the emitter will only produce more smoke or fire if there is space for it in the emitter region. Otherwise smoke or fire will always be produced and add up.

    初始温度

    Difference between the temperature of emitted smoke and the domain’s ambient temperature. This setting’s effect on smoke depends on the domain’s Heat Buoyancy.

    Density(密度)

    Amount of smoke to emit at once. Larger values result in more density being produced.

    燃料

    Amount of “fuel” being burned per second. Larger values result in larger flames, smaller values result in smaller flames:

    Comparison of flames with varying fuel rates.

    Fuel: 0.5.

    ../../../_images/physics_fluid_type_flow_fuelrate-1-0.png

    Fuel: 1.0.

    Vertex Group顶点组

    When set, use the specified to control where smoke is emitted.

    流来源

    This setting defines the method used to emit fluid.

    • 网格

      Emit fluid directly from the object’s mesh.

      • 表面发射

        Maximum distance in Voxels from the surface of the mesh in which fluid is emitted. Since this setting uses voxels to determine the distance, results will vary depending on the domain’s resolution.

      • Volume Emission Fire or Smoke Only:

    • Particle System Fire or Smoke Only:

      Create smoke or fire from a particle system on the flow object. which can be select with a .

      Note that only Emitter type particle systems can add smoke. See Particles for information on how to create a particle system.

    When enabled, the fluid will inherit the momentum of the flow source.

    源

    Factor for the inherited velocity. A value of 1 will emit fluid moving at the same speed as the source.

    法向

    This option controls how much velocity fluid is given along a face . Note that, initial velocities will always be applied along all face normals. Thus with a closed flow source mesh, fluid will always be emitted in more than one direction. To set initial velocities along only one direction all normals need to point in the same direction. This is can be achieved when using a plane as the flow object.

    Initial X, Y, Z

    Initial velocity along X, Y, Z coordinates in world space. This can be used in addition to the initial velocity along the Normal.

    参考

    类型

    流

    面板

    Physics ‣ Fluid ‣ Settings ‣ Texture

    When enabled, use the specified texture and settings to control where on the mesh smoke or fire can be emitted from. These settings have no effect on Outflow Flow Behavior.

    纹理

    A selector to choose the Texture.

    映射

    Controls whether to use or manual UV mapping.

    尺寸

    Overall texture scale.

    偏移量